––>

Work ready Vehicles

 


Drive Products is pleased to announce its Work Ready Vehicles available directly to it’s customers.

View All Vehicles

 

2019 Kenworth T-800 Tri Drive 22 Cube Stainless TC407 Tank EDWORD268260

March 28, 2019 2:51 pm
Filed Under: Acheson, Alberta, Edmonton, Fluid Tanks/Trailers, Kenworth, Kind, Make, New, Province/State, Type, Vehicles, Work Ready Vehicles

Truck Details: Model T-800 Conventional with 62″ Aerocab flattop sleeper Tri-Drive. x15 565 engine, 565 HP @ 2000 rpm, Fuller RTLO 18918B 18-speed Transmission. FGAWR 20,000lbs, RGAWR 69,000 lbs, c/w Powerhalt Positive air shutdown.

Equipment Details: 22 Cubic Meter (5,812 US Gallon nominal) TC 407, 316L Stainless Steel Non-Insulated, Two Compartment (shared vent), Transport Truck-Mount Tanks per the following:

Dimensions: 79.6″ID x 261″SW

Capacity: 22.81 Cubic Meters (6025.17 US Gallons) Max. Capacity to top of straight wall.

Shape: Straight Cylinder

Products: Light Crude S.G.=1.56

Maximum Product Weight: 13 pounds per gallon

Weight Laws: N/A

Product Temperature: 150 degrees F maximum temperature

Code Compliance: TC 407

Working Pressure: 25 PSI

Vacuum Relief: Based on the material thickness calculated for 25 PSI this vessel is capable of withstanding 10″ of inches mercury of negative pressure.

Tank Shell & Finish: 10 gauge T316L-2B Stainless Steel

Tank Heads: 7 gauge T316L-2B Stainless Steel ASME flanged & dished heads with single bulk head near center to have 4″ diameter vent hole at top of bulk head (7 ga. center baffle between both compartments).

Inside Weld Finish: All inside welds discolored removed.

Outside Weld Finish: All outside welds discoloration removed, striped & abrasive wheel buffed.

Baffles: (4) full 7 gauge T316LSS baffles with reinforced drain with pads at bottom, 4″ diameter vent at top and both sides, & 20″ diameter reinforced walk-through opening at center located equally spaced

Rings: N/A

Outriggers: 10 gauge T304 Stainless Steel

Frame Rails: Full length T304 Stainless Steel

Insulation: None

Manways: (4) 20″ diameter T316 Stainless Steel full opening chemical manhole cover with 6 hold downs and Buna N gasket, hinge pin at front and located near center and rear of each compartment: Betts #8310-LC-10

Spill Dam: Common stainless steel sides with no floor

Spill Dam Hose: (2) 1 ½” diameter drain hoses located one per side at rear of spill dam: Tigerflex

Roll Over: Stainless steel, integral part of spill dam

Clean Outs: (4) Betts 10″ lids

Vents: (2) total, 3″ pressure/vacuum vents located near center of each compartment: 3″ Girard DOT-407 pressure/vacuum vent with Tef-o-sil set at 25 PSI

Level Gauges: TD80 Titan Logix

Vapour Recovery: (2) 3″ air to open & spring to close stainless steel emergency valves with shear section elbow located one in each compartment. 3″ stainless line top of tank street side to rear and down rear head above rear frame terminating with 3″ TTMA butterfly and 3″ male adapter and cap: 3″ Betts #EV46110SSTS, 3″ TTMA Butterfly Valve w/ SS Disc/Stem & Teflon Seat

Air Unloading Line: None

Bottom Outlet: (2) 4″ air to open & spring to close butterfly valves with shear section elbow:

Emergency Valve Operator: Air toggle levers in street side front tank cabinet for valves and vapor vents for bottom valves. Remote fusible-toggle at street side rear of front fender

Valve Gaskets: Teflon Envelope

Piping: 4″ SCH 40 316 stainless steel piping

Walkway: 12″ wide aluminum grip full length curb side of spill dam with railing around outside of walkway

Ladder: (1) 16″ wide stainless steel ladder located on curbside with channel rung, walkway, and safety side rails

Rear Light Box: Stainless steel bolt on with 3 lights

Lights & Wiring: Truck-Lite LED lights with wire harness system and center directional lights with wiring in 1 ½” DIA stainless tube from front head to front of running gear

Junction Box: Junction box as required to tie in truck harness

Fenders: (2) from tool box to rear head to shell seam T=304

Bumper: TC Approved Stainless Steel

Hydraulic System: Drum cooler hydraulic system

Hose Carrier: On top of fenders, both sides with restraints

Thermometer: None

Paint: Prime and Paint all mild steel parts Standard Black – DO NOT PAINT STAINLESS STEEL

Conspicuity: 2″ wide Retro-Reflective Red/White stripes on both sides and rear

Placard Holders: Three in stainless steel

Data Plates: Data plates to be stamped in Metric Liters and Kg Canadian operation with CMVSS data plate and Vehicle Admissibility papers where applicable

Cabinets: Drivers side removable, with 4″ product pump, stainless piping and valves. Heated and insulated. Passengers side stainless storage cabinet.

Chain Hangers: Stainless steel roll out style

 

 

 



 

Services

No matter what your challenges are, Drive Products provides services that can solve them:

  • Custom Vehicle Rig-Ups
  • Fleet Programs and Services
  • Installation
  • Maintenance and Repair
  • Manufacturing
  • System Engineering & Design

View Services

 

Solutions

DRIVE Products has extensive expertise in developing solutions for the following industries.

  • Bulk Transport
  • Custom Engine Cooling
  • Driveline
  • Oil & Gas
  • Forestry
  • Refuse
  • Snow & Ice Removal
  • Towing & Recovery
  • Utility
  • Wetline Systems

View Solutions

 

Latest News

 

 

 

By Phone

TORONTO
1.800.668.6012
MONTREAL
1.800.361.9291
HALIFAX
1.866.661.7742
CALGARY
1.800.267.0559
EDMONTON
1.800.661.7335
TORONTO: UPFITTING AND
SERVICE CENTRE

1.800.668.6012
SUDBURY
1.855.586.1768

Need more contact info?

Customer Service by Branch Manager and Product Manager contact info.

Key Contacts for corporate leadership contact information.

 
Contact Us
Translate »